PRODUCT
CCI-305H (high-impedance type)
PRODUCT - Carbon film resistors conductive carbon paste - CCI-305H (high-impedance type)
Conductive carbon paste CCI-305H
CCI-305H type conductive carbon paste is a high-resistance carbon paste Senndai Electronic Materials Co., Ltd. production. It is made of special resin lapping and refined toner is made. Suitable for screen printing, for single-sided circuit board in part of the requirements to replace the resistive element has a fixed resistance silk screen lines. In FR2, FR4, copper-plated nickel coating film surface has excellent printability, abrasion resistance, solvent resistance, heat resistance and high hardness and strong adhesion.
- Features
- Parameters
- Dimensions
First, the performance indicators
1, packing: Toner
2, a solid content (WT%) 55-70%
3, a density (g / cm3) 1.2-1.3
4, the viscosity (dpa.s20%) 200-500 (VT-04E viscosity detector)
5, the coating area (cm2 / g) (depending on the film thickness) 100-200
6, square resistance (Ω / □ / 25.4цm) 0.5KΩ ~ 1MΩ
7, adhesion (3M600 tape, vertical pull) with no loss
8, hardness ≥5H
9, heat resistance (75 ℃ 1000hr) ± 10%
10, temperature characteristics (40 ℃ 95 ℃ RH 1000hr) ± 15%
11, high temperature 260 ℃ can be resistant to 5 seconds × 3 times
12, ultrasonic cleaning resistance, no cracks
Second, the use
1, the substrate FR2, FR4 copper-plated nickel coating film;
2, wire mesh stainless steel wire mesh or polyester screen printing;
3, diluent special thinner;
4, the curing process (recommended) oven 150 ℃ 30-45 minutes, IR; 175 ℃ 7-10 minutes
5, cleaning agents cyclohexanone;
6, the storage room temperature storage, unopened storage period at six months or more; (should avoid high temperature, high humidity preservation)
7, packaging 1.00 kg (or according to requirements)
Third, the operation and safety
1, using the metric or imperial 40-120T 100-305 mesh polyester or stainless steel screen printing, squeegee hardness of 65-80 degrees.
2. Stir thoroughly before use.
3, printing substrate must deal with clean, such as residual oil, oxides, thermoplastic resin, hand sweat and other contaminants when will severely reduce adhesion and electrical properties.
4, there must be enough carbon paste printing, otherwise it will affect the printing performance and carbon print thickness, resulting in changes in resistance.
5. In order to ensure consistent performance carbon printing should try to maintain the same viscosity; plus diluent should be mixed with the carbon paste close up some of the new carbon slurry, then an appropriate amount (less than 5%) were added after special thinner, stir uniform.
6, to be completely cured, otherwise it is impossible to obtain the desired properties, curing conditions depending on equipment required for fine-tuning.
7, CCI-305H conductive carbon paste containing a solution, should be kept well ventilated to prevent excess vapor inhalation, such as contact with the skin, should be promptly wash with water and soap, please do not go near the fire.
1, packing: Toner
2, a solid content (WT%) 55-70%
3, a density (g / cm3) 1.2-1.3
4, the viscosity (dpa.s20%) 200-500 (VT-04E viscosity detector)
5, the coating area (cm2 / g) (depending on the film thickness) 100-200
6, square resistance (Ω / □ / 25.4цm) 0.5KΩ ~ 1MΩ
7, adhesion (3M600 tape, vertical pull) with no loss
8, hardness ≥5H
9, heat resistance (75 ℃ 1000hr) ± 10%
10, temperature characteristics (40 ℃ 95 ℃ RH 1000hr) ± 15%
11, high temperature 260 ℃ can be resistant to 5 seconds × 3 times
12, ultrasonic cleaning resistance, no cracks
Second, the use
1, the substrate FR2, FR4 copper-plated nickel coating film;
2, wire mesh stainless steel wire mesh or polyester screen printing;
3, diluent special thinner;
4, the curing process (recommended) oven 150 ℃ 30-45 minutes, IR; 175 ℃ 7-10 minutes
5, cleaning agents cyclohexanone;
6, the storage room temperature storage, unopened storage period at six months or more; (should avoid high temperature, high humidity preservation)
7, packaging 1.00 kg (or according to requirements)
Third, the operation and safety
1, using the metric or imperial 40-120T 100-305 mesh polyester or stainless steel screen printing, squeegee hardness of 65-80 degrees.
2. Stir thoroughly before use.
3, printing substrate must deal with clean, such as residual oil, oxides, thermoplastic resin, hand sweat and other contaminants when will severely reduce adhesion and electrical properties.
4, there must be enough carbon paste printing, otherwise it will affect the printing performance and carbon print thickness, resulting in changes in resistance.
5. In order to ensure consistent performance carbon printing should try to maintain the same viscosity; plus diluent should be mixed with the carbon paste close up some of the new carbon slurry, then an appropriate amount (less than 5%) were added after special thinner, stir uniform.
6, to be completely cured, otherwise it is impossible to obtain the desired properties, curing conditions depending on equipment required for fine-tuning.
7, CCI-305H conductive carbon paste containing a solution, should be kept well ventilated to prevent excess vapor inhalation, such as contact with the skin, should be promptly wash with water and soap, please do not go near the fire.
CCI-305H type conductive carbon paste is a high-resistance carbon paste Chiyoda Electronic Materials Co., Ltd. production. It is made of special resin lapping and refined toner is made. Suitable for screen printing, for single-sided circuit board in part of the requirements to replace the resistive element has a fixed resistance silk screen lines. In FR2, FR4, copper-plated nickel coating film surface has excellent printability, abrasion resistance, solvent resistance, heat resistance and high hardness and strong adhesion.
